Direct Causes of Washing Machine Motor Failure
The most common reasons a washing machine motor stops working are burnt motor windings, a damaged start capacitor, or a faulty control board. Use a multimeter to check winding resistance; readings of 0 or infinity indicate burnt windings. A failed start capacitor cannot provide the energy needed for startup. Control board failure prevents normal voltage signals from reaching the motor. Additionally, power supply issues, broken drive belts, or seized bearings are frequent culprits.
How Washing Machine Motors Work
AC Motor Working Principle
Based on electromagnetic induction. Alternating current through the stator winding generates a rotating magnetic field, which cuts the rotor winding to induce current. The energized rotor rotates under electromagnetic force, driving the washer components.
DC Motor Working Principle
Based on energized coils rotating under force within a magnetic field. Direct current applied to the armature winding creates current-carrying conductors that receive electromagnetic torque in the stator field, rotating to drive the washing machine.
Comparison of Common Motor Types
| Motor Type | Key Features | Advantages | Application |
| Induction Motor | Simple structure, low manufacturing cost | Affordable, easy maintenance | Entry-level pulsator washers |
| Brushless DC Motor | Electronic commutation, no brush wear | Wide speed range, high efficiency, low noise, long life | Mid-to-high-end drum washers |
| Direct Drive Motor | No belt drive, directly connected to drum | High transmission efficiency, quieter, precise control, lower failure rate | Premium drum washers |
Key Motor Parameters and Fault Correlation
| Parameter | Normal Range | Abnormal Symptoms |
| Power | 300W - 800W | Insufficient power causes weak washing and poor spin performance; prolonged overload leads to burnout |
| Speed | Wash 300-600rpm / Spin 800-1600rpm | Abnormal speed results in incomplete washing or excessive water retention after spinning |
| Efficiency | High-efficiency motors exceed 85% | Reduced efficiency increases energy consumption and motor heating, accelerating insulation aging |
| Noise Level | Quality motors below 50dB | Noise exceeding 60dB usually indicates bearing wear or rotor eccentricity |
Step-by-Step Motor Troubleshooting Guide
Power and External Check
Confirm the power outlet is working by testing with another appliance. Check that the washer power cord is intact and the plug is secure. Ensure the washer door is fully closed, as most models have a safety lock that prevents motor startup when the door is open.
Fuse and Circuit Testing
Check whether the internal fuse has blown. Use a multimeter to measure voltage at the motor supply terminals; normal reading should be 220V. If voltage is present but the motor does not run, the fault lies in the motor itself. If no voltage is output, inspect the control board and relay.
Start Capacitor Testing
The start capacitor is critical for motor startup. When damaged, the motor may hum without rotating. Measure capacitance with a multimeter; normal value should be within ±10% of the rated capacity. If capacity has degraded by more than 20%, replace with a capacitor of identical specifications.
Winding Resistance Measurement
Disconnect motor wiring and measure resistance between windings with a multimeter. Normal windings should show resistance of several tens of ohms. A reading of 0 indicates a short circuit; infinity indicates an open circuit. Both conditions require motor replacement or rewinding.
Mechanical Component Inspection
Rotate the motor shaft manually; it should turn smoothly without binding. Difficult rotation may indicate dry bearings or foreign object obstruction. Check whether the drive belt is broken or loose, as belt issues cause the motor to spin while the drum remains stationary.
Other Common Motor Faults
Abnormal Noise During Operation
Severely worn motor bearings increase friction during rotation, producing abnormal noise. Loose mounting screws between the motor and washer housing cause resonance. Rotor eccentricity also generates unusual sounds. Stop the machine immediately upon detecting abnormal noise to prevent further damage.
Abnormal Motor Speed
Speed that is too high, too low, or unstable indicates a fault. For variable-speed motors, the speed control device may have failed. For induction motors, unstable power supply voltage may be the cause. Degraded start capacitor capacity reduces motor output power. Abnormal speed directly affects washing and spin performance and requires prompt repair.
Maintenance Tips to Extend Motor Life
Purchase Recommendations
For frequent washing of large or heavy items, select a motor with higher power and speed to ensure effective washing and spin performance.
For noise-sensitive environments, prioritize brushless DC motors or direct drive motors, with operating noise as low as 45dB.
Choose high-efficiency motors to reduce long-term operating costs. Grade 1 efficiency motors can save approximately 30% on annual electricity bills.
When to Replace the Motor
Recommended Replacement Cases
- Motor windings are burnt beyond repair
- Bearings are severely worn beyond repair
- Repair costs approach 60% of a new machine price
- Major motor failure in washers over 8 years old
Purchase Considerations
- Confirm power rating, speed, and mounting dimensions match the original
- Prioritize original brand parts
- Choose products from reputable Washing Machine Motor manufacturers
- Request warranty documentation; quality products typically offer 1-3 years
Hem 
+86-13968277871
